Furious FPV Mini RX for Frsky

Special Price $9.99 Regular Price $22.99
Out of stock
SKU
FPV-MINI-RX

Furious FPV Mini RX for Frsky

Furious FPV Mini RX for Frsky

This little receiver packs a big punch in a small package. Use this receiver with your Taranis
or other FrSky transmitter. It's an 8 channel, S-bus output, 500 meter range, full telemetry
receiver all in a form factor not much better than a US penny!

Click Here to watch a YouTube video that shows how to bind the Mini RX to your Taranis.

Features:

1. Mini size: 17x24 mm.
2. Light Weight: 2.11g 
3. Operating Range: 500m.
4. S-bus output without inverted (don’t need inverted on FC).
5. 8 channel output. 
6. Telemetry HUB.
7. Input voltage: 4-6V (normal 5V).
8. Compatibility: FrSky Taranis, Taranis Plus, & XJT module

NOTE: Regarding F3 chip, you need go to CLI on cleanflight and
set sbus_inversion = OFF
save

Configuration

Following, there’s some useful info for the setup and use of your Furious Mini RX.

1. Binding the receiver to the Frsky Taranis

  • In the Taranis, go to MODE SETUP (page 2) in the model configuration.
  • Go to Mode inside Internal RF and select D8.
  • Press and hold the receiver bind button and plug your battery in to turn the receiver on.
  • Release the button. A green LED lights up in the receiver.
  • Going back to the Taranis; we press BIND. The transmitter beeps, indicating it’s in bind mode.
  • Wait for the green LED on the receiver to turn off. The binding procedure has finished.
  • Exit the BIND mode in the Taranis.
  • Unplug the battery to turn off the receiver.

2. Binding the receiver to the XJT module

  • Using the dip switches of the XJT module, select the D8 mode. They shoud be in the following position: switch 1 = ON, switch 2 = OFF.
  • Press and hold the receiver bind button and plug your battery in to turn the receiver on.
  • Release the button. A green LED lights up in the receiver.
  • Press and hold the bind button and turn the transmitter on.
  • Release the button. A green light shoud blink in the module, indicating it’s in bind mode.
  • Wait for the green LED on the receiver to turn off. The binding procedure has finished.
  • Turn the transmitter off.
  • Unplug the battery to turn off the receiver.

    3. Receiver Configuration in the Cleanflight configurator

    • n the PORTS PORTS tab, select the UART that corresponds to the receiver (usually UART3 in F3 flight controllers) and activate Serial RX.
    • Save by clicking on the Save and Reboot button.
    • In the CONFIGURATION tab, in the Receiver Mode section, select RX_SERIAL.
    • In the same tab, in the Serial Receiver Provider section, select SBUS.
    • Save by clicking on the Save and Reboot button.
    • Go to CLI and type the following commands:
      set sbus_inversion = OFF
      save
      The FC will reboot, applying the change.
    • Go to the RECEIVER tab and make sure the receiver acts like it should.


    4. Telemetry Configuration:

    • In the PORTSPORTS tab, select the UART that corresponds to the telemetry (usually UART2 in F3 flight controllers) and select FrSky in Telemetry. Leave the baudrate to AUTO.
    • Go to CLI, and type the following commands:
      set telemetry_inversion = OFF
      save
      The FC will reboot, applying the change.
    • Make sure you’re getting thetelemetry values in our Taranis correctly.
    More Information
    Manufacturer Furious FPV
    Weight 2.1g
    Copyright © 2016 PitchRollYaw. All rights reserved.